 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| product specification 1 /34 lc370wun ver. 1.0 37.0 wuxga tft lcd title model general buyer *when you obtain standard approval, please use the above model name without suffix lc370wun *model sab1(rohs verified) suffix lg.philips lcd co., ltd. supplier for approval specification tv product development dept. lg. philips lcd co., ltd h.s. choi / engineer prepared by reviewed by signature date approved by please return 1 copy for your confirmation with your signature and comments. / / / signature date approved by ) ) ( ( final specification preliminary specification o.h. lee / manager j.h. lee / engineer
product specification 2 /34 lc370wun ver. 1.0 contents 26 handling precautions for protection film 9-6 10 signal timing specifications 3-3 25 precautions 9 25 mounting precautions 9-1 25 operating precautions 9-2 26 electrostatic discharge control 9-3 26 precautions for strong light exposure 9-4 26 storage 9-5 12 8 interface connections 3-2 color data reference 3-5 24 designation of lot mark 8-1 24 packing form 8-2 24 packing 8 23 emc 7-2 1 cover 2 contents 3 record of revisions 4 general description 1 5 absolute maximum ratings 2 6 electrical specifications 3 6 electrical characteristics 3-1 11 signal timing waveforms 3-4 13 power sequence 3-6 15 optical specifications 4 19 mechanical characteristics 5 22 reliability 6 23 international standards 7 23 safety 7-1 page item number product specification 3 /34 lc370wun ver. 1.0 final specification. - feb, 26, 2007 1.0 description page revision date revision no. record of revisions product specification 4 /34 lc370wun ver. 1.0 general features viewing angle free ( r/l 178 (typ.), u/d 178 (typ.) ) viewing angle (cr>10) 10-bit(d), 1.06 b colors color depth 1920 horiz. by 1080 vert. pixels, rgb stripe arrang ement pixel format 500 cd/m 2 (center 1point ,typ.) luminance, white total 132.14w (typ.) (logic=7.14 w, inverter=125w [vbr-a=1.65v] ) power consumption 9.0kg (typ.) weight transmissive mode, normally black display mode hard coating(3h), anti-glare treatment of the front polarizer (haze 13%) surface treatment 0.42675 mm x 0.42675 mm pixel pitch 877(h) x 516.8 (v) x 55.5 mm(d) (typ.) outline dimension 37 inches(940.091mm) diagonal active screen size 1. general description cn1 (51pin) lvds 2port source driver circuit tft - lcd panel (1920 rgb 1080 pixels) g1 s1 s1920 g1080 mini-lvds(rgb) timing controller gate driver circuit eeprom power circuit block sda scl +12.0v +24.0v, gnd, vbr-a, vbr-b the lc370wun is a color active matrix liquid crysta l display with an integral external electrode fluorescent lamp(eefl) backlight system. the matrix employs a-si thin film transistor as the active element. it is a transmissive display type which is operating in the normally black mode. it has a 37 i nch diagonally measured active display area with wuxga resolution (1080 vertical by 1920 horizontal pixel array). each pixel is divided into red, green and b lue sub-pixels or dots which are arrayed in vertica l stripes. gray scale or the luminance of the sub-pixel color is determined with a 10-bit gray scale signal for e ach dot. therefore, it can present a palette of more than 1. 06b (true) colors. it has been designed to apply the 10-bit 2-port lvds interface. it is intended to support lcd tv, pctv where high b rightness, super wide viewing angle, high color gam ut, high color depth and fast response time are importa nt. back light assembly 14pinx1cn(high) inverter(master) ai en ext vbr vbr out status product specification 5 /34 lc370wun ver. 1.0 note : 1. temperature and relative humidity range are shown in the figure below. wet bulb temperature should be 39 c max. and no condensation of water. 2. gravity mura can be guaranteed under 40 condition. the following items are maximum values which, if ex ceeded, may cause faulty operation or damage to the lcd module. table 1. absolute maximum ratings 2. absolute maximum ratings v dc +5.0 0 v br brightness control voltage note 1,2 c +50 0 t op operating temperature v dc +27.0 -0.3 v bl backlight inverter lcm unit %rh 90 10 h op operating ambient humidity %rh 90 10 h st storage humidity c +60 -20 t st storage temperature v dc +5. 25 -0.3 von/off on/off control voltage at 25 2 c v dc +14.0 +8.0 v lcd power input voltage max min parameter remark value symbol 90% 10 20 30 40 50 60 70 80 0 -20 0 10 20 30 40 50 dry bulb temperature [ c ] wet bulb temperature [ c ] storage operation humidity [(%)rh] 10% 40% 60% 60 product specification 6 /34 lc370wun ver. 1.0 it requires two power inputs. one is employed to po wer for the lcd circuit. the other is used for the eefl backlight and inverter circuit. table 2. electrical characteristics note : 1. the specified current and power consumpti on are under the v lcd =12.0v, 25 2 c, f v =60hz condition whereas mosaic pattern(8 x 6) is displaye d and f v is the frame frequency. 2. the current is specified at full white pattern. 3. the duration of rush current is about 2ms and ri sing time of power input is 1ms (min.). 1 ma 775 595 - 1 watt 9.3 7.14 - p lcd power consumption 3 a 4.0 - - i rush rush current v dc 12.6 12.0 11.4 v lcd power input voltage 2 ma 1035 795 - i lcd power input current circuit : parameter symbol max typ min note unit value 3. electrical specifications 3-1. electrical characteristics mosaic pattern(8 x 6) white : 255gray black : 0gray full white pattern white : 255 gray product specification 7 /34 lc370wun ver. 1.0 table 3. electrical characteristics (continue) power consumption ibl_b before aging ibl_a after aging power supply input current 4 hrs 50,000 life time 3 min 3 ts discharge stabilization time brightness adjust v br-a = 3.3v 2 a 6.8 6.5 - v br-a = 3.3v 1 a 6 5.7 - v br-a = 1.65v 1 w 132 125 - pbl v br-a = 1.65v 1 a 5.5 5.2 - 1 vp-p 0.5 - - power supply input voltage ripple v br-a = 1.65v 2 a 6.3 6 - 1 v bl = 22.8v v br-b = 3.3v v br-a = 1.65v a 8 - - irush power supply input current (in-rush) v 3.3 - 0 v br-b lamp: inverter : vdc 3.3 1.65 0.0 v br-a brightness adjust input voltage for control system signals vdc 25.2 24.0 22.8 vbl power supply input voltage on/off off on vdc 5.0 - 2.5 v on vdc 0.8 0.0 -0.3 v off parameter symbol max typ min notes unit values notes : 1. electrical characteristics are determined after the unit has been on and stable for approximately 120 minutes at 25 2 c. the specified current and power consumption are under the typical supply input voltage 24vand v br (v br-a : 1.65v & v br-b :3.3v), it is total power consumption. the ripple voltage of the power supply input voltag e is under 0.5 vp-p. lpl recommend input voltage is 24.0v 5%. 2. electrical characteristics are determined within 30 minutes at 25 2 c. the specified currents are under the typical supply input voltage 24v. 3. the brightness of the lamp after lighted for 5mi nutes is defined as 100%. ts is the time required for the brightness of the c enter of the lamp to be not less than 95% at typica l current. the screen of lcd module may be partially dark by t he time the brightness of lamp is stable after tur n on. 4. specified values are for a single lamp which is aligned horizontally. the life time is determined as the time which lumin ance of the lamp is 50% compared to that of initial value at the typical lamp current (v br-a : 1.65v & v br-b :3.3v), on condition of continuous operating at 25 2 c 5. the duration of rush current is about 20 ms. product specification 8 /34 lc370wun ver. 1.0 table 4. module connector(cn1) pin configuration - lcd connector(cn1): fi-r51s-hf(manufactured by jae ) - mating connector : fi-r51hl(jae) or compatible this lcd module employs two kinds of interface conn ection, a 51-pin connector is used for the module electronics and master 14-pin connector is used for the integral backlight system. 3-2-1. lcd module 3-2. interface connections note : 1. the pin no 44 is lcd test option. agp (auto gen eration lcm operates pattern) or nsb (no signal black) is case that lvds signals are out of frequen cy or abnormal condition in spite of 12 volt power supply. lpl recommends nsb. ( agp : vcc or ope n / nsb : gnd ) 2. all gnd(ground) pins should be connected togethe r to the lcd modules metal frame. 3. all vlcd (power input) pins should be connected together. 4. all input levels of lvds signals are based on th e iea 664 standard. 5. specific pins(pin no. #1~#10) are used for inter nal data process of the lcd module. if not used, these pins are no connection. 6. if dcr function should be enable(h), 10th pin must be connected to serial resistor which value is under 1k ohm. - 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 no - power supply +12.0v power supply +12.0v power supply +12.0v power supply +12.0v no connection ground ground ground no connection or gnd no connection or gnd second channel 4+ second channel 4- second channel 3+ second channel 3- ground second clock channel c+ second clock channel c- ground second channel 2+ second channel 2- second channel 1+ second channel 1- second channel 0+ second channel 0- l =8bit, h =10bit(d) description - vlcd vlcd vlcd vlcd nc gnd gnd gnd reserved reserved re4p re4n re3p re3n gnd reclkp reclkn gnd re2p re2n re1p re1n re0p re0n bit sel symbol first channel 4+ ro4p 25 first channel 4- ro4n 24 first channel 3+ ro3p 23 first channel 3- ro3n 22 ground gnd 21 first channel 1+ ro1p 15 first channel 1- ro1n 14 first channel 0+ ro0p 13 first channel 0- ro0n 12 ground gnd 11 no connection nc 2 no connection nc 3 no connection nc 4 no connection nc 5 no connection nc 6 h = jeida, l = vesa lvds select 7 ext_vbr vbr_ext 8 ver_out vbr_out 9 l=off,h=on dcr_en 10 first channel 2- ro2n 16 first channel 2+ ro2n 17 ground gnd 18 first clock channel c- roclkn 19 first clock channel c+ roclkp 20 no connection or gnd reserved 26 description symbol no gnd ground 1 product specification 9 /34 lc370wun ver. 1.0 inverter connector : s14b-ph-smc (manufactured by jst) or equivalent - mating connector : phr-14 or equivalent table 5. inverter connector pin configulation 3-2-2. backlight inverter rear view of lcm pcb 14 1 2, 3 analog dimming voltage dc 0.0v ~ 3.3v (typ : 1.65v) v br-a 11 0.0v ~ 5.0v v on/off 12 4 normal : upper 3.0v abnormal : under 0.7v status 14 3 backlight ground gnd 7 backlight ground gnd 8 1 burst dimming voltage dc 0.0v ~ 3.3v v br - b 13 backlight ground gnd 10 backlight ground gnd 9 backlight ground gnd 6 power supply +24.0v v bl 5 power supply +24.0v v bl 4 power supply +24.0v v bl 3 power supply +24.0v v bl 2 power supply +24.0v v bl 1 note description symbol pin no note : 1. gnd should be connected to the lcd modu les metal frame. 2. if pin #11 is open, vbr-a = 1.65v. when apply o ver 1.65v( ~ 3.3v)continuously, its luminance is increasing however lamps life tim e is decreasing. it could be usable for boost up luminance when usin g dcr (=dynamic contrast ratio) function only. 3. minimum brightness : vbr-b =0v maximum brightne ss : vbr-b = 3.3v 4. even though pin #14 is open, there is no effect on inverter operating, the output terminal of inve rter. 5. each impedance of pin #11,12 and 13 is 150[k ? ] , 200[k ? ] and 150[k ? ]. product specification 10 /34 lc370wun ver. 1.0 table 6. timing table for ntsc (de only mode) table 6 shows the signal timing required at the inp ut of the lvds transmitter. all of the interface s ignal timing should be satisfied with the following specificatio n for normal operation. 3-3. signal timing specifications horizontal vertical lines 86 45 10 tvb blank lines - 1080 - tvv display period lines 1166 1125 1090 tvp total total blank display period thp thb thv symbol 2200/2 tclk 1280 1100 1032 tclk 320 140 72 tclk - 960 - note unit max typ min item frequency vertical horizontal dclk fv fh fclk symbol hz 63 60 57 khz 70.9 67.5 64.1 148.5/2 mhz 78 74.25 70.5 note unit max typ min item table 7. timing table for pal (de only mode) note : the input of hsync & vsync signal does not h ave an effect on normal operation(de only mode). the performance of the electro-optical characterist ics may be influenced by variance of the vertical r efresh rate. table 7 shows the signal timing required at the inp ut of the lvds transmitter. all of the interface s ignal timing should be satisfied with the following specificatio n for normal operation. horizontal vertical lines 300 270 228 tvb blank lines - 1080 - tvv display period lines 1380 1350 1308 tvp total total blank display period thp thb thv symbol 2200/2 tclk 1280 1100 1032 tclk 320 140 72 tclk - 960 - note unit max typ min item frequency vertical horizontal dclk fv fh fclk symbol hz 52.5 50 47.5 khz 70.9 67.5 64.1 148.5/2 mhz 78 74.25 70.5 note unit max typ min item product specification 11 /34 lc370wun ver. 1.0 0.7vdd 0.3vdd t clk invalid data valid data invalid data invalid data invalid data pixel 0,0 pixel 2,0 pixel 1,0 pixel 3,0 de(data enable) valid data 0.5 vdd t hp t hbp t hv t hfp t vp t wv t vbp t vv t vfp hsync vsync de(data enable) de(data enable) dclk first data second data de, data t wh 3-4. signal timing waveforms * thb = thfp + twh +thbp * tvb = tvfp + twv +tvbp * reference : sync. relation product specification 12 /34 lc370wun ver. 1.0 the brightness of each primary color(red,green,blue ) is based on the 10-bit gray scale data input for t he color. the higher binary input, the brighter the color. ta ble 10 provides a reference for color versus data i nput. table 8. color data reference 3-5. color data reference 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (000) green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 green (001) ... ... ...... ... ... ... 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 green (1022) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 green (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (000) red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 red (001) ... ... ... ...... ... ... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 red (1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red (1023) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (001) ... ...... ... ... ... ... 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (1022) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (1023) blue (000) white yellow magenta cyan blue (1023) green (1023) red (1023) black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic color 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 blue blue blue blue msb lsb green green green green msb lsb red redred red msb lsb b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 g9 g8 g7 g6 g5 g4 g3 g2 g1 g0 r9 r8 r7 r6 r5 r4 r3 r2 r1 r0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue color input color data product specification 13 /34 lc370wun ver. 1.0 3-6. power sequence 3-6-1. lcd driving circuit table 9. power sequence 10% 0v 90% 10% t 1 t 2 t 5 t 6 lamp on t 3 t 4 t 7 t 8 90% invalid data invalid data interface signal (tx) power for lamp power supply for lcd v lcd option signal (lvds_select, dcr_enable, bit_select) 0v valid data - t2 - - 4 4 5 3 3 4 notes s - - 2.0 t6 ms 0 t8 ms 0 t7 ms - - 0 t2 ms ms - - 200 t3 - - 200 t4 ms - - 0 t5 ms 20 - 0.5 t1 max typ min unit value parameter note : 1. please avoid floating state of interface signal at invalid period. 2. when the interface signal is invalid, be sure to pull down the power supply v lcd to 0v. 3. the t3/t4 is recommended value, the case when fa iled to meet a minimum specification, abnormal display would be shown. there is no reliab ility problem. 4. if the on time of signals(interface signal and o ption signals) precedes the on time of power(v lcd ), check the lcd logic power(vcc) is under 0.8v, other wise it will be happened abnormal display. 5. t6 should be measured after the module has been f ully discharged between power off and on period. product specification 14 /34 lc370wun ver. 1.0 3-6-2. sequence for inverter power supply for inverter v on/off v bl 10% 0v 90% t 1 t 2 t 3 t 2 0.7v t 4 24v (typ.) t 5 lamp on t 4 t7 1000ms (min) 1000ms (min) table 10. power sequence for inverter 3-6-3. deep condition for inverter v bl (typ.) x 0.8 0 v v bl : 24v t6 v bl (typ) x 0.8 ms 10 - - t6 3 ms - - 1000 t7 - ms - - 10 t5 2 ms 0 t4 1 remarks ms - - 500 t2 ms - - 200 t3 ms - - 20 t1 max typ min units values parameter v br-a & v br-b notes : 1. t1 describes rising time of 0v to 24v an d this parameter does not applied at restarting tim e. 2. t4(max) is less than t2. 3. in t7 section, vbr-a should be more than 1.65v an d vbr-b should be 3.3v product specification 15 /34 lc370wun ver. 1.0 table 11. optical characteristics ta= 25 2 c , v lcd =12.0v, f v =60hz, dclk=148.5mhz vbr_a=1.65v, vbr_b=3.3v lcd module optical stage(x,y) pritchard 880 or equivalent 50cm 3 1.3 - - 5p white 1 - 1300 900 cr - - mprt gray-to-gray - - - 6 gray scale y axis, down ( =270 ) y axis, up ( =90 ) x axis, left ( =180 ) x axis, right( =0 ) - - 89 d - - 89 u - - 89 l 5 degree - - 89 r viewing angle (cr>10) white blue green red 0.607 gy 0.291 gx 0.062 by 0.145 bx 0.292 wy 0.279 wx ms 0.334 ry typ +0.03 0.638 typ -0.03 rx color coordinates [cie1931] 4 8 5 - g to g response time luminance variation 2 cd/m 2 - 500 400 l wh surface luminance, white note unit contrast ratio max typ min value symbol parameter fig. 1 optical characteristic measurement equipment and method optical characteristics are determined after the un it has been on and stable in a dark environment at 25 2 c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig. 1 shows additional information concerning the measurement equipment and method. 4. optical specification product specification 16 /34 lc370wun ver. 1.0 table 12. gray scale specification 100 88.17 74.66 63.37 53.00 43.96 35.56 28.21 22.36 17.06 12.05 7.75 4.51 2.07 1.08 0.20 0.08 luminance [%] (typ.) l959 l1023 l639 l703 l767 l831 l447 l511 l575 l895 l191 l255 l319 l383 l127 l63 l0 gray level note :1. contrast ratio(cr) is defined mathematica lly as : cr(contrast ratio) = maximum crn (n=1, 2, 3, 4, 5) surface luminance at position n with all white pixe ls crn = surface luminance at position n with all black pixe ls n = the position number(1, 2, 3, 4, 5). for more i nformation, see fig 2. 2. surface luminance are determined after the unit has been on and 30min after lighting the backlight in a dark environment at 25 2 c. surface luminance is the luminance value at cen ter 1-point across the lcd surface 50cm from the surfac e with all pixels displaying white. for more information see the fig. 2. 3. the variation in surface luminance , white is defined as : white(5p) = maximum(l on1 ,l on2 , l on3 , l on4 , l on5 ) / minimum(l on1 ,l on2 , l on3 , l on4 , l on5 ) where lon1 to lon5 are the luminance with all pixel s displaying white at 5 locations . for more information, see the fig. 2. 4. response time is the time required for the displ ay to transition from g(n) to g(m) (rise time, tr r ) and from g(m) to g(n) (decay time, tr d ). for additional information see the fig. 3. (n product specification 19 /34 lc370wun ver. 1.0 table 13 provides general mechanical characteristic s. 5. mechanical characteristics table 13. mechanical characteristics value item 460.89 mm vertical 9000(typ.)/9500(max) weight 469.8 mm vertical 516.8 mm vertical 55.5 mm depth 819.36 mm horizontal active display area 828.6 mm horizontal bezel area 877.0 mm horizontal outline dimension note : please refer to a mechanic drawing in terms of tolerance at the next page. product specification 20 /34 lc370wun ver. 1.0 product specification 21 /34 lc370wun ver. 1.0 product specification 22 /34 lc370wun ver. 1.0 6. reliability table 14. environment test condition note : before and after reliability test, lcm sho uld be operated with normal function. ta= 40 c ,90%rh humidity condition operation 7 0 - 15,000 ft 0 - 40,000 ft altitude operating storage / shipment 8 shock level : 50grms waveform : half sine wave, 11ms direction : x, y, z one time each direction shock test (non-operating) 6 wave form : random vibration level : 1.0grms bandwidth : 10-300hz duration : x,y,z, 30 min one time each direction vibration test (non-operating) 5 ta= 0 c 240h low temperature operation test 4 ta= 50 c 50%rh 240h high temperature operation test 3 ta= -20 c 240h low temperature storage test 2 ta= 60 c 240h high temperature storage test 1 condition test item no. product specification 23 /34 lc370wun ver. 1.0 7. international standards 7-1. safety a) ul 60065, 7 th edition, dated june 30, 2003, underwriters laborato ries, inc., standard for audio, video and similar electronic ap paratus. b) can/csa c22.2, no. 60065:03, canadian standards association, standard for audio, video and similar electronic ap paratus. c) iec60065:2001, 7 th edition cb-scheme and en 60065:2002, safety requirements for audio, video and similar el ectronic apparatus.. 7-2. emc a) ansi c63.4 methods of measurement of radio-nois e emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 b) cispr13 "limits and methods of measurement of r adio interference characteristics of sound and television broadcast receivers and associated e quipment" cispr22 "limits and methods of measurement of radi o interference characteristics of information technology equipment" international special commit tee on radio interference. c) en55013 "limits and methods of measurement of ra dio interference characteristics of sound and television broadcast receivers and associated equip ment" en55022 "limits and methods of measurement of radio interference characteristics of information technology equipment" european committee for elect ro technical standardization.(cenelec), 1988(including a1:2000) product specification 24 /34 lc370wun ver. 1.0 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m note 1. year b) location of lot mark 2. month serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 4 2 1 dec mar feb jan 8. packing mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 a) package quantity in one box : 4 pcs b) box size : 968mm x 366mm x 595mm a,b,c : size(inch) d : year e : month f ~ m : serial no. product specification 25 /34 lc370wun ver. 1.0 please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using specified mountin g holes (details refer to the drawings). (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit b reak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzine. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions 9. precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required ti me that brightness is stable after turned on) becomes longer (4) be careful for condensation at sudden temperatu re change.condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shal l be done by system manufacturers. grounding and shieldi ng methods may be important to minimized the interference. (7) please do not give any mechanical and/or acoust ical impact to lcm. otherwise, lcm cant be operated its full characteristics perfectly. (8) a screw which is fastened up the steels should be a machine screw. (if not, it can causes conductive particles and dea l lcm a fatal blow) (9) please do not set lcd on its edge. (10) it is recommended to avoid the signal cable an d conductive material over the inverter transformer for it can cause the abnormal display and temperatu re rising. product specification 26 /34 lc370wun ver. 1.0 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the te mperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. 9-5. storage 9-6. handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape . when the protection film is peeled off, static elec tricity is generated between the film and polarizer . this should be peeled off slowly and carefully by p eople who are electrically grounded and with well i on- blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel surface or its vestige is recog nized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with norma l- hexane. product specification 27 /34 lc370wun ver. 1.0 note: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd103 or compatible) 3. 9 means msb and 0 means lsb at r,g,b pixel dat a. # appendix-i-1 required signal assignment for flat link (thine : th c63lvd103) transmitter(pin7 =l) host system 30 bit red0 red1 red2 red3 red4 red5 red6 red7 red8 red9 green0 green1 green2 green3 green4 green5 green6 green7 green8 green9 blue0 blue1 blue2 blue3 blue4 blue5 blue6 blue7 blue8 blue9 hsync vsync data enable clock 33 34 35 36 37 38 59 61 4 5 40 41 42 44 45 46 62 63 6 8 48 49 50 52 53 54 64 1 9 11 55 57 58 12 ta- ta+ tb- tb+ tc- tc+ tclk- tclk+ td- td+ te- te+ thc63lvd103 or compatible timing controller 100 100 100 100 100 100 ro0n ro0p ro1n ro1p ro2n ro2p roclkn roclkp ro3n ro3p ro4n ro4p vesa / jeida fi-re51s-hf 12 13 14 15 16 17 19 20 22 23 24 25 7 31 30 29 28 25 24 23 22 21 20 19 18 lcm module gnd product specification 28 /34 lc370wun ver. 1.0 note: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd103 or compatible) 3. 9 means msb and 0 means lsb at r,g,b pixel dat a. # appendix-i-2 required signal assignment for flat link (thine : th c63lvd823) transmitter(pin7 =h) host system 30 bit red0 red1 red2 red3 red4 red5 red6 red7 red8 red9 green0 green1 green2 green3 green4 green5 green6 green7 green8 green9 blue0 blue1 blue2 blue3 blue4 blue5 blue6 blue7 blue8 blue9 hsync vsync data enable clock ta- ta+ tb- tb+ tc- tc+ tclk- tclk+ td- td+ te- te+ thc63lvd103 or compatible timing controller 100 100 100 100 100 100 ro0n ro0p ro1n ro1p ro2n ro2p roclkn roclkp ro3n ro3p ro4n ro4p vesa / jeida fi-re51s-hf 12 13 14 15 16 17 19 20 22 23 24 25 7 31 30 29 28 25 24 23 22 21 20 19 18 lcm module vcc 45 59 61 33 34 35 36 37 38 6 8 62 63 40 41 42 44 45 46 9 11 64 1 48 49 50 52 53 54 55 57 58 12 product specification 29 /34 lc370wun ver. 1.0 LC370WUN-SAB1 packing assy # appendix- -1 paper_dw3 box 6 opp 70mmx300m tape 7 yupo paper 100x100 label 8 eps packing, top r_l 5 eps packing, bottom 4 masking 20mm x 50m tape 3 al bag 2 lcd module 1 material description no. product specification 30 /34 lc370wun ver. 1.0 LC370WUN-SAB1 pallet assy # appendix 2 # appendix- -2 opp tape 5 yupo paper label 4 clip 18mm band, clip 7 pp band 6 dw3 angle, cover 3 plywood_1140x990x130 pallet 2 packing assy 1 material description no. product specification 31 /34 lc370wun ver. 1.0 # appendix 2 lcm label model serial no. ul, tuv mark lpl logo us patent no. origin rohs verified made in korea lc370wun (sa)(b1) # appendix- -3 8 serial no. (see cas 24page for more information) 1 2 3 4 5 6 7 9 10 11 12 inch m assy factory code serial no. 13 month year product specification 32 /34 lc370wun ver. 1.0 # appendix 3 box label pallet label # appendix- -4 12 pcs lot/mm-dd lc370wun sab1 made in korea rohs verified * * * * * * * * * * * * * * * * lc370wun sab1 4 pcs l o t/mm-dd * * * * * * * * * * * * * * * * made in korea rohs verified product specification 33 /34 lc370wun ver. 1.0 # appendix- -1 lcm dcr only 100 0.01 luminance [%] dcr on vbr-a = 1.65v l239 l255 l159 l175 l191 l207 l111 l127 l143 l223 l47 l63 l79 l95 l31 l15 l0 gray level from system (vbr_ext pin) from t-con (asic) vbr_out (v br -b) signal source 1300 : 1 10,000 : 1 dcr level 1.65v or nc 1.65v or nc v br -a 3.3v 0v ~ 3.3v v br -b off (0v) on(3.3v) dcr_enable dcr_enable option pin description lcm control board lcm control board lcm control board lcm control board system system system system board board board board lcm lcm lcm lcm inverter inverter inverter inverter 14 1414 14 1 11 1 12v 12v 12v 12v 51 5151 51 1 11 1 nc / 1.65v nc / 1.65v nc / 1.65v nc / 1.65v v vv v br brbr br - -- - a aa a 3.3v 3.3v 3.3v 3.3v v vv v br brbr br - -- - b bb b 3.3v 3.3v 3.3v 3.3v # 10 # 10 # 10 # 10 dcr_enable pin dcr_enable pin dcr_enable pin dcr_enable pin ntsc / pal ntsc / pal ntsc / pal ntsc / pal sync_pwm sync_pwm sync_pwm sync_pwm ffc cable ffc cable ffc cable ffc cable vbr vbr vbr vbr- -- - b bb b 13 1313 13 11 1111 11 pin : vbr_out pin : vbr_out pin : vbr_out pin : vbr_out pin : vbr_ext pin : vbr_ext pin : vbr_ext pin : vbr_ext product specification 34 /34 lc370wun ver. 1.0 # appendix- -2 note : 1. to make dcr max (bare cr)x10, v br-a and v br-b must be given by system. 2. dcr max 10,000:1 is defined mathematically as : dcr = maximum dcrn (n=1, 2, 3, 4, 5) surface luminance at position n with all white pixe ls (v br-b =3.3v, v br-a =1.65v) dcrn = surface luminance at position n with all black pixe ls (v br-b =0v, v br-a =0v) n = the position number(1, 2, 3, 4, 5). for more i nformation, see fig 2. 3. measurement sequence (aging time 10 min each pa ttern) : turn on lcm measure black luminance (v br-b =0v, v br-a =0v) measure white luminance (v br-b =3.3v, v br-a =1.65v) 4. in case the lowest minimum brightness is continu ed, it can affect the lamp reliability and appear the p artial darkness. 1300 : 1 13,000:1 dcr level 1.65v 0v ~ 1.65v v br-a 3.3v 0v ~ 3.3v v br-b system dcr (dynamic contrast ratio)- max 13,000:1 system system system system board board board board lcm control board lcm control board lcm control board lcm control board lcm lcm lcm lcm inverter inverter inverter inverter 14 1414 14 1 11 1 51 5151 51 1 11 1 12v 12v 12v 12v 51 5151 51 1 11 1 0v ~ 3.3v 0v ~ 3.3v 0v ~ 3.3v 0v ~ 3.3v v vv v br brbr br- -- - a aa a 0v ~ 3.3v 0v ~ 3.3v 0v ~ 3.3v 0v ~ 3.3v v vv v br brbr br- -- - b bb b ntsc / pal ntsc / pal ntsc / pal ntsc / pal sync_pwm sync_pwm sync_pwm sync_pwm ffc cable ffc cable ffc cable ffc cable 13 1313 13 11 1111 11 # 10 : dcr enable pin # 10 : dcr enable pin # 10 : dcr enable pin # 10 : dcr enable pin maximum brightness (100%) (dcr condition) v br-b : 3.3v v br-a : 1.65v minimum brightness (10%) 0v function v br-a,b voltage |
Price & Availability of LC370WUN-SAB1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |